Home
Forums
New posts
Search forums
What's new
New posts
Latest activity
Members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
Current visitors
Menu
Log in
Register
Navigation
Install the app
Install
More options
Contact us
Close Menu
Home
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Martin_J's latest activity
Martin_J
replied to the thread
Boat cover fixings
.
Or here at Point North.. SMALL LACING BUTTON - WHITE PLASTIC
15 Apr 2024
Martin_J
replied to the thread
Gennaker mast head U bolt size
.
I'm not on board at the moment to check my spare... but I really seem to think that it's the larger one of those Selden ones used at the...
14 Apr 2024
Martin_J
reacted to
Travelling Westerly's post
in the thread
Gennaker mast head U bolt size
with
Like
.
Ah fantastic help, thanks team, much appreciated. I do indeed have a Selden/Kemp mast. I had no idea it could be a Selden U bolt. I...
14 Apr 2024
Martin_J
reacted to
Bouba's post
in the thread
Small is …..errr cheaper
with
Like
.
If you buy one...there are only three possible outcomes (non of which are bad)....either you will realize it’s time to swallow the...
14 Apr 2024
Martin_J
replied to the thread
Gennaker mast head U bolt size
.
The Selden ones that I mentioned, I also seem to think, have small lumps on them that allow you to tighten then into place so they don't...
14 Apr 2024
Martin_J
replied to the thread
Gennaker mast head U bolt size
.
If you have a Selden mast, are you sure it wasn't a Selden offset/bent U-bolt.. A bit more expensive than a standard u-bolt but it...
14 Apr 2024
Martin_J
replied to the thread
Volvo Saildrive 130S - water in oil
.
Oh and you've already mentioned replacing the larger o-rings that seal between the bearing carrier and the leg. Easy.
13 Apr 2024
Martin_J
replied to the thread
Volvo Saildrive 130S - water in oil
.
If the shaft seals have done nine years, they've done rather well. It's not hard to replace the sea water seal and the oil seal on...
13 Apr 2024
Martin_J
replied to the thread
Seized stainless steel turnbuckle!?
.
I've was going to suggest the recommended way to turn the rigging screw is a spanner across the centre rather than through the middle...
13 Apr 2024
Martin_J
replied to the thread
Whitlock Cobra 5R delux
.
I don't feel any notchiness on mine... Have you tried disconnecting the linear drive (usually just an R clip to remove) and what was...
13 Apr 2024
Martin_J
replied to the thread
Whitlock Cobra 5R delux
.
Maybe your shims were removed in the past. They're actually rather thin.
13 Apr 2024
Martin_J
replied to the thread
Whitlock Cobra 5R delux
.
The actual 5R deluxe shims are also shown in the first set of PDFs...
13 Apr 2024
Martin_J
replied to the thread
Whitlock Cobra 5R delux
.
You can see the shims on that Cobra 6 manual (pasted below) and they look just like the slim white plastic shims shown in my very first...
13 Apr 2024
Martin_J
replied to the thread
Whitlock Cobra 5R delux
.
Maintenence guide suggests removing a shim if you have more than 10mm play at the wheel outside edge... You mentioned notchiness so I...
13 Apr 2024
Martin_J
replied to the thread
Ocean Safety MOB1
.
Remember, the MOB1 needs to be configured with the parent vessel MMSI in order for the VHF on the parent vessel to receive the DSC...
12 Apr 2024
Home
Members
Top